Ongoing recruitment at KOHASA Engineering Company Limited

KOHASA Engineering Company Limited is a wholly indigenous onshore and offshore Oil & Gas Production Facilities Design and Construction company with a big reservoir of experience in different fields of engineering.

We are recruiting to fill the positions below:

Job Title: Principal E3D / PDMS Administrator

Location: Nigeria

Job Description / Responsibilities

• Produce / prepare 3D Implementation plans in line with client Specification / requirements.
• Conversant with ExxonMobil GPs Requirement regarding PMDS/E3D specifications / procedure / requirements for multiple platforms CATS/SPECS/MACRO database set up.
• Project set up, maintenance and support of the system.
• The PDMS / E3D administrator will maintain all areas of the 3D model environment for stability and maintenance.
• The Administrator shall ensure the modeling environment works appropriately in regard to the generation, control and distribution of 3D model interfaces.
• Project set-up, administration and user support for Aveva PDMS / E3D / E3D.
• Full and through knowledge of PDMS / E3D Ver 12.1.0.14, E3D, Paragon, PML, CATS & SPECS
• Review overall plot plan of the project & divide the plant to optimum number of construction areas in consultation.
• Understands the scope of each project and has the capability to create PDMS / E3D database structures that will enable the 3D design and subsequent creation of deliverables from the project databases.
• Create PDMS / E3D model based on 3D modeling procedure with the required databases, teams and users and access rights
• according to PDMS / E3D Administration, Audit & control. (Establish procedures / specifications for projects and company standards relating to use of PDMS / E3D.)
• Responsible for end-user training on the usage of customization.
• This includes class room / remote training and preparation of training material.
• Interact directly with users / discipline leads and document requirements and special needs related to project designs and needs.
• Coordinate with the designers from the respective engineering disciplines to meet the project deliverables with timeliness and quality.
• Troubleshoot and escalate appropriately any technical issues and follow-up for quick resolution.
• Project specific customization of system and writing macros as per project needs and for further checking the quality of PDMS / E3D outputs.
• Follow established PDMS/E3D standards, Setup the PDMS/E3D and related systems, Maintain the PDMS/E3D project, Provide direction and support to designers
• Provide ad hoc reports from PDMS/E3D or related databases
• Develops staffing schedules to ensure the most advantageous utilization of available equipment.
• Assists in developing plans for hardware and/or software purchases
• Coordinates installation of new systems with user schedules
• Oversees and provides technical support for customized tools, utilities and scripts to automate work processes and improve CAD productivity and efficiency; oversees and participates in performing daily maintenance on CAD databases, including researching and reconciling inconsistencies and variations in data
• Perform routine checks on model through data verification and project auditing.
• Create required reports from PDMS/E3D model for Layout / Material groups.
• Extract MTO from PDMS/E3D model for uploading to VPRM or any material management system used in the project.
• Upload specification files generated by VPRM in PDMS/E3D & check the completeness and correctness of items uploaded in PDMS/E3D.
• Setup ISODRAFT module for generating isometrics as per project & client specifications / documents & resolve and trouble shoot isometric errors.
• Update model review files in NAVIS WORKS format on daily basis and copy them to project server for the use of all discipline engineers.
• DESIGN-Equipment, Piping, Structural, Access ways.
• ISODRAFT-ISODRAFT Customization as per the Requirements, Bolt table, Backing Sheet.
• Draft-Administration -Administration & Drafting.
• Auto Drawing Production Methodology(ADP)
• Paragon CATS)-Piping, Steel, Instrument, Catalogue creation & updating
• SPECON (SPECS)-Piping, Steel, Instrument, Spec creation.& updating
• LEXICON-UDA creation.
• PROPCON-Properties Table Creation.
• ADMIN- Project Set up, Access Control, Project Creation, configurations
• MDS- Multi-Discipline Support setup and customization
• Reports Customization as per the requirements
• Customization and creating routine for 3D Model file export and import integration with fabrication detailing software & Engineering analysis software.
• Creation and preparation Of Macro from PML Suitable For Any PDMS/E3D Module and PML-2 Object orientated programming.
• Transfer of specification Generated in other to PDMS/E3D & Generation of specification from piping specification.
• Proficient in uploading of backing sheet in PGA`s & Isometrics as per project need.
• Report Extraction as required with project suit.
• PDMS/E3D suite of software installation and trouble shooting
• PDMS/E3D project architecture and Databases
• Well versed in P&ID`S, other department drawings like equipment G.A.D, Hook up etc.
• Co-Ordination with other department for generation of Catalogue & clash free model.
• Familiar with pipe supports & CEASER-II software.
• Conversant with international codes and standards such as ANSI, ASTM, API, ASME and BS.
• Detailed piping specification, valve specification, specialty items specification, Material selection/ specialty items creation from primitive on E3D.
• Supervise and groom Designers.

Educational and Qualifications

• Master’s Degree in Engineering or B.Sc in Engineering, COREN certified
• Years of Work Experience required: minimum of 8 years
• Age: 35 – 40 years.

Job Title: Reliability and Maintenance Specialist

Location: Nigeria

Job Description / Responsibilities

• The Specialist will develop and lead reliability improvement processes by working closely with Clients Project Management
• Team as well as their Operations & Maintenance Organization.

In addition, the candidate will:

• Identify and evaluate risk and reliability improvement opportunities through assessments of plant and associated data.
• Establish reliability models in all phases of engineering (pre-FEED to DED) and on operating facilities.
• Lead cross discipline assessment teams, including coaching and mentoring in reliability values and techniques.
• Utilize reliability analysis tools to identify priorities and focus the organization on the most significant improvement opportunities.
• Work closely with Project Teams to build reliability and maintainability into the facility design.
• Develop procedures in line with equipment criticality and to comply with legislation and company standards.

Educational and Qualifications

• Bachelor’s Degree in Engineering, Registered Professional Engineer (or non-USA equivalent)
• Years of Work Experience required: Minimum of 8 years demonstrable experience in the reliability environment, preferably in the Oil and Gas Industry with good knowledge of all risk analysis techniques including RAM, QRA, FTA, FMEA and SIL.
• Age: 35-40 years.

 

Job Title: Lead, Process Engineering

Location: Nigeria

Job Description / Responsibilities

• Plans, schedules, and supervises process design and or systems work for onshore and offshore oil and gas facilities projects.
• Reviews scopes of work, budgets, commitments, schedules and progress. Makes use of progress reporting system.
• The degree of assistance and supervision depends on scope , phase and progress of project
• Review and management of project and general specifications, engineering procedures and engineering policy.
• Candidates must contribute efficiently to the all kinds of process related activities related to oil and gas activities for projects, studies, proposals, estimates and / or work improvement programs. The Lead Process Engineer will be responsible for project execution within budget and time schedules, management and leading other engineers, and must be able to work independently
• However complex matters may be discussed with a Process Specialist in the department.

The Lead Process Engineer must perform and will be held responsible for and aware of:

• Scheduling and estimating activities
• Establishing the definition of basis of design and design criteria.
• Consult specialists of the Process Technology Department and elsewhere , if applicable.
• Perform feasibility, alternative evaluation and process planning studies
• Role and sensitivity of process operating pressures and temperature, stream analysis and properties
• Selection of process schemes and process operating philosophy.
• Preparation and maintenance of process flow diagrams including heat and material balances
• Preparation and maintenance of process data.
• Preparation and maintenance of mechanical design conditions for large process plants.
• Preparation of process and mechanical design specifications of equipment, lines and instrumentation.
• Preparation and maintenance of piping and instrument diagrams. Lead in screening meetings and communication with other
• disciplines to verify and ensure that process requirements are will understood and properly taken cares of by all concerned.
• Preparation and maintenance of hydrostatic test diagrams and safeguarding diagrams.
• Execution of all process calculations and simulations.
• Preparation and maintenance of all safety and environmental aspects.
• Preparation and maintenance of plant operation manuals
• Review of all piping designs which may affect the process integrity.
• In respect of constructed plants is the representative for all process related aspects such as commissioning, start-up and test
• runs.

Educational and Qualifications

• Bachelor’s Degree in Chemical or Mechanical Engineering
• Years of Work Experience required: 10 years working experiences in the discipline, 10 years should be working on oil field, petrochemical, or oil and gas handling projects
• Age: 35-40 years.

 

Job Title: Major Rotating Equipment (Compressor and Turbines) Controls, Instrumentation and Automation Specialist

Location: Nigeria

Job Description / Responsibilities

• Be in charge of Compressors and Gas Turbines controls and Instrumentation.
• Conduct remote diagnostics and monitoring of equipment..
• Use software in resolving vibration issues.
• Align and support compressor and Turbine system improvement programs that will minimize/eliminate deferment.
• Support and Sustain Compressor and Turbine systems. Implement and sustain Knowledge transfer to respective asset team personnel.

Educational and Qualifications

• Engineering Degree in the relevant discipline
• Years of Work Experience required: 10 years cognitive experience
• Age: 35-40 years.

 

Job Title: QA / QC and Structures Integrity Specialist

Location: Nigeria

Job Description / Responsibilities

• Ensure all QA/QC services within the projects /Asset to ensure that services are delivered to specified standards.
• Hold regular engagement with SPDC PQL on weekly basis to review outcome of all the QA/QC services under his watch and produce minutes of meeting for signature by SPDC.
• Plan and direct activities of Facility Statutory Inspectors and On-Plot Piping Inspection Teams, inspection assignments in SQI
• Plan and organise additional ad-hoc inspection activities as and when required
• Maintain a clear and efficient filing system of all QA/QC activities
• Conduct weekly review of reports in SQI; including all findings , NCR, Observations etc.
• Hold copies of current calibration certificates for all NDT equipment used in performance of the services.
• Coordinate the deployment of key QA/QC services around SPDC offshore facilities.
• Define and develop the project Integrated Quality Management System, to achieve flawless and defect free delivery, in line with the requirements of industry and global standards.
• Ensure Quality management is focused on risk-based thinking, setting clear requirements and providing quality insights, based on “Plan-Do-Check-Act” phases
• Develop and implement project Quality Discipline Delivery Plan.
• Develop Quality intervention programs to address risks and opportunities, optimize cost and add values
• Provide input relevant to quality risks and management activities into PEP.

Educational and Qualifications

• Engineering Degree and Planning Certification,
• Years of Work Experience required: Minimum of 8 years operating, precommissioning / commissioning experience in hydrocarbon facilities
• Age: 35-40 years.

 

Job Title: Commissioning and Start-Up Specialist (Instrument, Control & Automation)

Location: Nigeria

Job Description / Responsibilities

• Review, advise and monitor the implementation of Integration & communication links with multiple DCS & Process Automation properitarty system.
• Integrate Safety Instrumented System with multiple properitory DCS system and platforms in accordance with standards and statutory requirements. Review and assist to develop the Commissioning test protocols covering all Process
• Automation system Project ITPs, covering all key project activities and work locations, Monitor, review and report to PQL /PL with respect with SATs, FATsWelding Procedures, Close out of Punchlists Control Loops logic modification and testing Quality related programmes, Alarm & Limits, Control loop performance checks , Audit Schedules and Results, etc.
• Coordinate ITP Inspection , FAT and SAT at activities at various sites and vendors, review and comment and assist to implement the design control system logic.

Educational and Qualifications

• B. Eng / B.Sc in relevant Engineering discipline
• Years of Work Experience required: Minimum of 10 years operating, precommissioning/ commissioning experience in hydrocarbon facilities
• Age: 35-40 years.

 

Job Title: Commissioning & Start-Up Specialist (Process / Mechanical)

Location: Nigeria

Job Description / Responsibilities

• Overseeing completion of multi-discipline division of work related to pre-commissioning or commissioning on projects.
• Supporting and supervision of the commissioning team on projects.
• Provides multi-discipline input into the scheduling, designing and planning of projects. In addition, the Commissioning Lead also develops multi-discipline commissioning strategy documents for projects.
• Review, approve and overseeing the installation and design of minor temporary commissioning supplies and systems.
• Review and approve all multi-discipline commissioning processes to ensure they are compliant with the procedures, specifications and standards of the project.
• Ensure that all commissioning procedures follow all appropriate safety practices and procedures and participate in all project and company safety programs.
• Audit commissioning activities regularly to ensure compliance with environmental, quality, and safety requirements.
• Communicate with the project engineering office in order to make sure that the applicable fabrication drawings are created in accordance with all commissioning requirements.

Educational and Qualifications

• Engineering Degree and Planning Certification, must be COREN certified
• Years of Work Experience required: Minimum of 10 years operating, precommissioning / commissioning experience
• Age: 35 – 40 years.

Job Title: Lead, I & CA

Location: Nigeria

Job Description / Responsibilities

• The Lead I & CA Engineer shall be responsible for the team coordination / timely provision of appropriate Instrumentation inputs in line with the various projects as defined in the scope of work for the specific project
• In addition, he shall be able to develop new approaches to problems, prepare or modify drawings, specifications, calculations, and monitor work to comply with applicable codes and standards.
• Be able to use design tools and software like AutoCAD, SPI (INtools), InstruCalc to carry out design works and studies and prepare design reports (i.e. philosophies, specifications & datasheets, study reports, procedures), calculation sheets/notes, design drawings as well as conduct site visits to any project site without supervision or guidance.

Educational and Qualifications

• Engineering Degree and Planning Certification, must be COREN certified
• Years of work experience required: minimum of 10 years operating, precommissioning/ commissioning experience
• Age: 35 – 40 years.

How to Apply
Interested and qualified candidates should send their CV to: hr@kohasaeng.com using the Job Title as the subject of the email.

Application Deadline 15th February, 2021.